(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
This page gives a brief overview of the various arp-scan options. It does not go into detail - for that, see the help output or read the man pages.
Target selection options
| Long Option |
Short Option |
Description
|
| --file |
-f |
Read the list of targets from the specified file
|
| --localnet |
-l |
Generate the list of targets from the outgoing interface address and netmask
|
| --random |
-R |
Randomise the target list so hosts are scanned in a random order
|
| --numeric |
-N |
Only allow IP addresses, no hostnames. Never perform DNS lookup
|
If neither the --file or --localnet options are specified, then targets must be specified as arguments. The target argument can either be a list of addresses or names, an IP network in the form <network>/<bits> or <network>:<netmask>, or a range of IP addresses in <start>-<end> format.
Network interface options
| Long Option |
Short Option |
Description |
Default
|
| --interface |
-I |
Specify the network interface to use |
First up, configured, non-loopback interface
|
| --snap |
-n |
Specify the frame capture length |
64 Bytes
|
Outgoing Ethernet Frame Options
| Long Option |
Short Option |
Header Field |
Default
|
| --destaddr |
-T |
Destination Address |
FF:FF:FF:FF:FF:FF (Ethernet broadcast)
|
| --srcaddr |
-S |
Source Address |
Outgoing interface address
|
| --prototype |
-y |
Protocol Type |
0x0806 (ARP)
|
| --padding |
-A |
N/A |
No padding (added by network driver)
|
| --llc |
-L |
N/A |
Ethernet-II Framing
|
| --vlan |
-Q |
N/A |
No 802.1Q tag
|
Outgoing ARP Packet Options
| Long Option |
Short Option |
ARP Field |
Default
|
| --arphrd |
-H |
ar$hrd |
1 (Ethernet)
|
| --arppro |
-p |
ar$pro |
0x0800 (IPv4)
|
| --arphln |
-a |
ar$hln |
6 (Ethernet address length)
|
| --arppln |
-P |
ar$pln |
4 (IPv4 address length)
|
| --arpop |
-o |
ar$op |
1 (ARP Request)
|
| --arpsha |
-u |
ar$sha |
Outgoing interface h/w address
|
| --arpspa |
-s |
ar$spa |
Outgoing interface IP address
|
| --arptha |
-w |
ar$tha |
zero (00:00:00:00:00:00)
|
The ARP field ar$tpa is set to the target IP address.
Outgoing packet timing options
| Long Option |
Short Option |
Description |
Default
|
| --retry |
-r |
Total number of ARP request attempts for each target address |
2
|
| --timeout |
-t |
Timeout in milliseconds |
500
|
| --interval |
-i |
Inter-packet interval |
Calculated from bandwidth
|
| --bandwidth |
-B |
Outbound Bandwidth |
256,000 bits/sec
|
| --backoff |
-b |
Timeout backoff factor |
1.5
|
Received packet decoding and display options
| Long Option |
Short Option |
Description
|
| --quiet |
-q |
Don't decode Vendor string
|
| --ignoredups |
-g |
Don't display duplicate ARP responses
|
| --ouifile |
-O |
Specify location of IEEE OUI MAC/Vendor file
|
| --iabfile |
-F |
Specify location of IEEE OUI MAC/Vendor file
|
| --macfile |
-m |
Specify location of manual MAC/Vendor file
|
| --pcapsavefile |
-W |
Write received packets to pcap savefile
|
| --rtt |
-D |
Display the packet round-trip time
|
Miscellanous Options
| Long Option |
Short Option |
Description
|
| --help |
-h |
Display usage message and exit
|
| --verbose |
-v |
Display extra debugging information
|
| --version |
-V |
Display arp-scan program version and exit
|
